The X-Carve Pro uses GRBL based firmware. Specific firmware can be found here: https://github.com/inventables/grbl-xcp
The official grbl wiki can be found here: https://github.com/grbl/grbl
Firmware Settings
You can find and change firmware settings using Easel's Machine Inspector.
To check the Stock Firmware Settings click on your machine here:
How to find Firmware Settings
Turn on your machine, connect to Easel and open any project. In your project, go to Machine > General Settings > Machine Inspector. If your machine is powered on and connected you will see your Firmware settings listed under Console.
How to update X-Carve Pro Firmware
If you have outdated firmware, when clicking "Carve" you will see a banner that prompts you to upload new firmware. You can update by following the prompts.
Alternatively, you can manually upload firmware by connecting your machine to Easel and clicking "Carve" to "unlock without homing."
Next, go to Machine > General Settings > Upload Firmware and follow the prompts.
Once the firmware is uploaded, you will have to refresh Easel to reconnect.
How to change individual Firmware Settings
Open the Machine Inspector (Machine > General Settings > Machine Inspector). In the Console, type your new settings into the box one at a time, then press enter. Do this for each incorrect setting. Example:
$1=255
Enter
Then, once you have corrected all the settings you can send the command:
$$
This will display your Firmware settings there in the command line, you can ensure that all of your changes are saved. If you want to see the settings at the bottom, there is a small refresh on the right side of the settings box, or close out of the Machine Inspector and re-enter it.
X-Carve Pro 4 x 4
Latest Firmware Version (10/31/2023): Grbl 1.1h-XCPd.20230214a
This is the only version we currently support.
$10 and $40 may show up as settings. These do not affect movement or travel, they are only used to report GRBL messages. Ensure $40=0.
$0=10 $1=255 $2=0 $3=14 $4=0 $5=0 $6=0 $10=115 $11=0.020 $12=0.002 $13=0 $20=0 $21=0 $22=1 $23=3 $24=25.000 $25=750.000 $26=250 $27=2.000 $30=24000 $31=0 $32=0
$40=0 $100=42.353 $101=42.353 $102=160.000 $110=7620.000 $111=7620.000 $112=2540.000 $120=250.000 $121=350.000 $122=500.000 $130=1219.200 $131=1219.200 $132=130
X-Carve Pro 4 x 2
Latest Firmware Version (10/31/2023): Grbl 1.1h-XCPd.20230214a
This is the only version we currently support.
$10 and $40 may show up as settings. These do not affect movement or travel, they are only used to report GRBL messages. Ensure $40=0.
$0=10 $1=255 $2=0 $3=14 $4=0 $5=0 $6=0 $10=115 $11=0.020 $12=0.002 $13=0 $20=0 $21=0 $22=1 $23=3 $24=25.000 $25=750.000 $26=250 $27=2.000 $30=24000 $31=0 $32=0
$40=0 $100=42.353 $101=42.353 $102=160.000 $110=7620.000 $111=7620.000 $112=2540.000 $120=250.000 $121=350.000 $122=500.000 $130=1219.200 $131=609.200 $132=130